Texas Flame Operator Certification Practice Test

These questions are part of the practice quiz. Start practicing

• True or False: When control functions are required, an effect valve is not needed.
• Which of the following best describes the scope of a Site Inspection for flame effects?
• Which Flame Groups have unattended as a feature?
• Fire props can be refueled after waiting 30 minutes following extinguishment. True or False?
• Fuel-soaked waste disposal should follow which guidance?
• Which flame effect appliance uses fuel from a prepackaged single-use container?
• Name an Example of a Flame Group VII Type Effect.
• Which scenario would be a Flame Group VII Type Effect?
• NFPA 1126 standard covers what?
• What is the purpose of Safety Shutdown (Lockout) in flame effect systems?
• What action is performed first after the last firing of a flame effect?
• Each flame effect shall be provided with an automatic fuel shutoff valve (the effect valve), installed upstream of the burner. Where should this valve be located?
• Which document is used to convey information to the AHJ for evaluating a flame effect for permit application?
• True or False: The arming of the effect shall be manually or automatically monitored and confirmed until the effect is fired.
• How many spotters are required for each performance and rehearsal with fire?
• What is reaction time?
• What must flame effect control systems be designed and installed to do?
• How should a Hazard Area surrounding a Flame Effect be monitored?
• Which features must be present on each prepackaged single-use container receiver?
• What topics should be included in additional training for spotters/firewatch?
• Which groups are included in the Fire Hazard Evaluation coordination?
• MSDS stands for Material Safety Data Sheets.
• Flame Effect Materials are identified by what characteristic at standard conditions?
• What post-performance procedure applies to fire props?
• What is required prior to any changes to a performance for a Fire Performer?
• Firing by methods other than the opening of a manual or electrically actuated fuel release valve may be acceptable.
• Direct Ignition
• NFPA 160 and NFPA 1126 standards are required for audiences of at least how many people?
• Hybrid Flame Effect is defined as
• What action should be taken immediately after the flame effect concludes if safety systems were interrupted?
• Which Flame Groups have main show control as a feature?
• What is the minimum control requirement for Flame Group VII?
• Which Flame Groups have automatic flame verification as a feature?
• Which method encourages the operator to monitor the area by requiring them to look toward the flame when enabling?
• What does AHJ stand for in fire protection regulation language?
• Is it permissible to handle flame effect materials or devices while under the influence of alcohol, narcotics, or judgment-impairing drugs?
• Which statement about the operation of emergency stop stations is true?
• If ambient temperature is critical to proper operation, what must manufacturers specify?
• Which entity approves the emergency operations plan?
• Which fuel type is used by a Liquid-Fuel Flame Effect Appliance?
• How must accumulators be designed, manufactured, certified and tested?
• Which Group Type Effect does not require a control system designed to ensure against accidental firing?
• An operator can demonstrate competency by experience and training or by holding a license acceptable to the AHJ.
• Liquid Fuel?
• Gaseous-Fuel Flame Effect Appliance uses what as primary fuel?
• Which statement describes a component not listed among the described flame effect valves and controls?
• Which statement about protection of control system components is true?
• What is the minimum rating for additional extinguishers (not water) accessible to firewatch/spotters for a temporary installation?
• Which device is directly responsive to ignition device attributes necessary for safe operation?
• Control systems must be inoperable unless a Flame Operator intentionally does two actions: 1. Deliberately applies control power. 2. Enables or Arms the control system.
• Which of the following actions helps prevent operator complacency during repetitive enabling?
• How often should flame effects be inspected for normal and safe operating condition and/or retested for operation as designed and anticipated?
• Which option correctly defines Group III Flame Effect?
• Which on-site personnel is specifically required for pyrotechnic events in Texas?
• When should the plan be reviewed with the AHJ, Flame Effect Operator(s), and the Building Owner or Representative?
• What is the Arm in flame effect control?
• When should fire and life safety systems that have been interrupted be restored?
• Under what condition can fire protection and Life Safety Features be interrupted for permanently installed indoor flame effects?
• Which term refers to materials used as fuel for flame effects and classified by their phase at STP?
• NFPA 160 Standard Covers What?
• Which Flame Groups have attended as a feature?
• Which statement describes Flame Group I Type Effect?
• Which of the following best defines the Holding Area in flame effect operations?
• True or False: The fuel supply and auxiliary services necessary to the operation of the flame effect control system (compressed air supply, oxidizers, additives, etc.) shall be permitted to be turned on prior to the activation of control power.
• Name an Example of a Flame Group III Type Effect
• Mixing what with fuel while inside an accumulator is prohibited?
• Evidence of insurance is not required at permit application?
• Which statement best describes the relationship between control power and intentional action for flame effect systems?
• Where should fueling for a Fire Performer occur?
• Separation between the performer and the audience shall be maintained to prevent fuel or flame contact with audience members as approved by the AHJ.
• Solid-Fuel Flame Effect Appliance uses primary fuel?
• In flame safety, which event triggers a Safety Shutdown (Lockout)?
• What is a Permit?
• True or False: Smoking can be permitted by performers as a part of a performance with a flame effect.
• What is required regarding the ignition source for liquid-fuel flame effect appliances?
• Which description defines Group V Flame Effect?
• If a licensee's license or permit has been revoked, how long must they wait before reapplying?
• What defines a Supervisory Control System in flame effects?
• Which of the following is NOT an example of a Flame Group I Type Effect?
• What additional training should be provided to spotters/firewatch?
• Which option best defines the Enable function in a flame control system?
• Which two flame groups do not contain permanent installation as a feature?
• What is required to move a fuel-soaked wick through an audience for a fire performer?
• For a hybrid flame effect, which NFPA standards apply to the respective portions?
• When does the enable process begin?
• Which term describes a pilot flame supervised by a primary safety control?
• Smoking and other ignition sources shall be prohibited within what distance of the fueling area?
• True or False: Personal computers, single-board controllers, and other systems that have control capability but that are not routinely used in protective applications can be used as life safety controllers.
• Group I Flame Effects are characterized by which control style?
• Group II Flame Effects can be installed outdoors only. Which option correctly reflects this restriction?
• NFPA stands for which organization?
• In NFPA 160, which valve type is identified as a Safety Shut-off Valve?
• Flame Effect Materials are defined as?
• Who is responsible for the emergency pre-show announcement?
• The document that provides safety information about chemicals used in fueling operations is known as what?
• LPG is an acronym for which fuel?
• Texas Administrative Code Section 34.8 covers what?
• Besides the operator, to whom should the operating instructions be made available?
• When external pressure sources are used with flame effect appliances, what design requirement must be provided?
• True or False: Performers and support personnel can be forced to be in the area of a flame effect in the performance of their duties.
• Does an assistant need to be licensed as a Flame Operator?
• Where should the operating power for firing any flame effect originate?
• What are the requirements for valves on an accumulator?
• Spill containment during refilling of containers is required when approved by which entity?
• According to an infrared surface thermometer, what is the maximum exposed skin temperature for audience members?
• What provision is required to remove unused liquid fuel from the system?
• Can a municipality impose stricter flame effects regulations than these standards?
• What must standby personnel be able to do in case of an alarm?
• LNG stands for which fuel?
• Which description defines Group V Flame Effect?
• Which of the following is a required characteristic of an emergency stop in automatically controlled flame effects?
• If a Hazard Area is not actively monitored by a person (or PME), what two alternatives are acceptable?
• Which approvals are required to interrupt portions of a fire protection and life safety system?
• Non-effect safety controllers should not be used to allow, trigger, or request safety-critical action unless signals of these non-effect safety controllers are intercepted and qualified by an effect safety controller that has responsibility for allowing safety-critical actions.
• True or False: Where required for operation and maintenance, control systems can have separate sources of control power.
• Where should spotters/firewatch be positioned?
• Which term describes a flame effect that is supervised and fired by an automatic control system?
• Fueling stations for Fire Performers must be attended by who whenever a hazard is present?
• What device ensures a shutoff is automatic for each flame effect?
• Flame Effect Safety Controller?
• What is a Flame Effect Operator inspecting as part of their Site Inspection?
• Flame effect systems shall be maintained to design specifications. True or False?
• Which statement is true about AHJ involvement in flame effects approvals?
• Which scenario would be included in Flame Group III Type Effect?
• Which step is required before any changes to a fire performance?
• Who must approve all flame effects?
• True or False: A flame effect does not need to be manually or automatically armed before firing.
• In a flame effects production, which term describes the performers participating in the show that includes flame effects?
• Which statement best describes Flame Group II Type Effect?
• Occupation Code Chapter 2154 covers what?
• When is a pressure supervisory control system required in order to prevent operation of a liquid-fuel flame appliance?
• In addition to reapplying after a revocation, what must the licensee request?
• What are spotters/firewatch in charge of?
• Direct Ignition is defined as
• Which entity has the authority to accept or deny requests related to flame effects or pyrotechnics within a jurisdiction?
• Which Flame Groups have manual fuel controls as a feature?
• What is the minimum rating for water extinguishers accessible to firewatch/spotters for a temporary installation?
• How is the Safety Shutoff Valve characterized?
• Compared to a public display permit, the minimum liability insurance for a flame or pyrotechnic effect permit is:
• What area must be observed by the operator throughout the entire period the flame effect is enabled and fired?
• Fire Watch is best described as
• What is the purpose of a Man in the Loop in flame effects safety?
• Which statement about Fire Hazard Evaluations is true?
• Which statement defines Temporary Installation?
• Spill containment shall be used during refilling of containers as approved by the AHJ.
• Which description best defines a Design Plan for a flame effect?
• Which description defines Group II Flame Effect?
• Which statement correctly describes a design consideration for Liquid-Fuel Flame Effect Appliances?
• Name an example of an interlock that can be included in flame effect control systems.
• Which valve is located between the two safety shutoff valves?
• What is the daily holding area quantity rule for flammable flame effect materials?
• A Fire Hazards Evaluation may be required under which circumstance?
• Which term refers to the area made hazardous by the operation of the flame effect?
• Fire refers to
• Which element is required to be included in the Flame Effect Site Plan?
• Manually operated emergency stop control stations must maintain their actuated state until when?
• Which NFPA standards must be adhered to when using pyrotechnic ignitors with flame effects?
• Which of the following is an example of a Flame Group I Type Effect?
• What role does a fire watch play in interrupting during flame effects operation?
• Which general safety measures should be observed for flame effect systems and portable flame effects?
• True or False: Portable accumulators are allowed to be moved to a safe location for discharge.
• Which statement about testing fire props is correct?
• How should fuel-soaked waste be stored or disposed of?
• What should be provided when cast members can be present immediately before arming and firing the flame effect?
• Define 'open flame' as used in the regulations.
• Minimum control requirements for Flame Group II Flame Effect include which of the following?
• Which feature describes a 'deadman style switch' for PME devices?
• Where should PME devices be located to ensure operator safety?
• Name an Example of a Flame Group III Type Effect.
• What type of flame effects can approval be sought in order to interrupt, partially, fire protection and life safety systems?
• Under what condition may bare skin be permitted within a flame effect?
• Flame Effect Operator?
• The volume of fuel stored in an accumulator tank shall be no more than what is required to produce the desired flame effect.
• Which term specifically describes a flame effect that is supervised and fired by an automatic control system?
• Who must first approve of smoking by performers as part of a performance with a flame effect?
• What must be performed prior to installation with prepackaged single-use containers?
• How is the minimum tank size for liquefied flammable gas flame effects determined?
• Which of the following is an example of Flame Group II Type Effect?
• Fail-Safe means
• What is the location of the effect valve relative to the burner?
• Which of the following is NOT an acceptable method for emergency stop and shutdown of a manually controlled flame effect?
• Prepackaged Single-Use Container Fuel Flame Effect Appliance uses fuel from what?
• Which term refers to a circuit or mechanism that, when actuated, results in the complete shutdown and extinguishment of all flame effects controlled by it?
• Group I Flame Effect is described as?
• For temporary installations, which additional extinguishers are required beyond those normally provided?
• Which is an example of a monitored condition that could trigger the emergency stop when the limit is exceeded?
• What must a supervisor station be provided the means to do with regards to the shut-off valve?
• Which term describes an attended, manually controlled flame effect?
• Who has the power to suspend, revoke, or refuse to issue or renew a Flame Operator's license?
• Which statement about use permits is true?
• Which flame groups have both attended and automatic fuel controls?
• Who can be permitted to be in the area of a flame effect?
• True or False: The AHJ can require a walk-through and a representative demonstration of the flame effects before approval.
• The volume of the accumulator can exceed what is required to produce the desired flame effect.
• Documentation for testing flame effects should come from whom?
• How far from the fueling area is the audience prohibited from entering?
• The Flame Effect System Classification and General Requirements do not apply to which type of person?
• During temperature testing of flame effects, at what rate should the flame be operated to obtain readings?
• Flame Effect is defined as
• The Fire term refers to the sequence of control system functions that result in the deliberate release of fuel for ignition.
• Only fuels expressly manufactured for burner or combustion applications and specified by the manufacturer of a flame effect appliance shall be used as flame effect fuels for that appliance.
• Standby fire safety personnel must meet which requirements?
• What does PME stand for in flame effect safety?
• Which of the following is NOT a safety feature required for Group II through Group VII control systems?
• How long is a Pyrotechnic or Flame Operator's license valid before renewal is required?
• What is the minimum age of a Flame Effect Operator?
• Which of the following is true regarding automatic control of flame effect groups?
• Which group types must be attended while connected to a fuel source?
• For Flame Group I Flame Effect, what are the minimum control requirements?
• Which event must occur before the enable process continues?
• Which description matches the Flame Effect System?
• Which scenario would be a Flame Group II Type Effect?
• Which precaution should a Fire Performer take with excess fuel, residue, fuel-soaked waste etc.?
• Who bears the burden of proving that a license or permit should be granted when reapplying after revocation?
• Which term describes the plan that presents design criteria and assumptions used in the flame effect design?
• How must prepackaged single-use containers be disposed of?
• Liquid-Fuel Flame Effect Appliance uses what as primary fuel?
• Which groups are, or can be, automatically controlled?
• What is the recommended stance on spotters' visibility of hazards?
• Ignition detection devices are allowed even if they can produce false-positives due to false sensing of ignition devices, pilots, or flame effects or due to false sensing of other non-fire-related devices normally present in the local environment as long as other fail-safes are provided.
• Where and with what can reassembled flame effect piping systems that are designed to be separated into subassemblies be leak tested?
• What does the use permit expiration address for a temporary flame effect?
• Where should the fueling area be located and how should it relate to the audience?
• Which mechanism can de-energize a control system to permit unattended operation?
• How often should fire props be tested to verify operation?
• How far past the anticipated flame contact zone must a shafted prop be made of fire resistant material or be covered?
• In Flame Group II, what ensures shut-off occurs in the event of a failure?
• When are control systems permitted to be unattended?
• How many criteria are required for the emergency stop and complete shutdown of an automatically controlled flame effect?
• Fire Watch is best described as the assignment of a person or persons to an area for the express purpose of
• Which item is included in the Flame Effect Plan Content?
• Accessible Hazard Area is defined as
• Flame effects testing: true or false?
• Which entity has the authority to approve performer smoking in a flame effects performance?
• Paint, starting fluid, air fresheners, lubricants, hairsprays, and insecticides are prohibited for use as flame effect fuels.
• For Flame Group V, which statement about the interface between the flame effect control system and the main show control is correct?
• True or False: Once a device is armed it only needs to be confirmed once as long as it has not been fired.
• What is required for overpressure protection in liquid-fuel flame effect systems?
• Venues should have what for areas both visible to and out of sight of the technical director, where a person might be exposed to injury during firing?
• When should the accessible hazard area be under direct observation by the operator or assistant(s) firing the flame effect?
• Which of the following are acceptable firing methods for flame effects?
• In flame effects operations, the Assistant is
• When flame effects are used inside a building, what must the building have or provide acceptable to the authority having jurisdiction?
• What is the maximum allowed temperature rise for combustible materials above ambient after equilibrium is reached?
• What does the term Safety-Critical mean?
• True or False: Liability insurance policy must be issued by an insurer authorized to do business in Texas and countersigned by a licensed Texas insurance agent.
• Which flame group explicitly requires a fuel supervisory station with fuel pressure limit switches?
• What is required to store quantities in excess of daily usage in holding areas?
• Who approves the location for refilling and pressurizing refillable liquid-fuel containers?
• When portable flame effects are not in use, how should they be stored?
• What is a 'safety container' as defined in the rules?
• What is the definition of a Solid-Fuel Flame Effect Appliance?
• Which statement regarding varying timing of the flame effect is correct?
• Which NFPA 160 personnel is NOT listed?
• Accessible Hazard Area is defined as
• What is required when cast members or moving set pieces are present in the hazard area immediately before or after arming and firing?
• Control systems are designed to prevent harm to humans, animals or equipment.
• Are safety interlocks required to be Fail-Safe?
• Who is required to specify a minimum and maximum ambient temperature rating for flame effect appliances when it is critical to proper operation?
• True or False: Smoking is allowed in areas where fuels used in flame effects are present?
• What procedures should be included in the Operating Procedures of a Flame Effect?
• DoT stands for what?
• Which Flame Group's controls are designed by the designer and acceptable to AHJ?
• What is a Primary Safety Control ★?
• Where is the automatic fuel shutoff valve (effect valve) located?
• Which group should review the Flame Effect Plan to ensure coordinated emergency response?
• Are performers and support personnel allowed to be in the flame effect area, and under what condition?
• Which controller has responsibility for allowing safety-critical actions in a flame effect control system?
• Who is responsible for the storage, setup, operations, and teardown of all flame effect materials, devices, equipment, systems, and supervision of assistants?
• What must the permit applicant provide with the application regarding insurance?
• Accumulator design regulations may come from which organizations for gas pressure safety?
• Disposal of fuel-soaked waste must be in accordance with which requirements?
• Can a pre-packaged single-use container be refilled?
• Under which condition is a flame effect considered armed via manual confirmation?
• Which component is the last fuel shutoff valve before the flame effect burner?
• All flame effect devices and materials shall have drawings, manuals, or written descriptions describing the type of item and performance specifications.
• Gaseous Fuel is defined as?
• Which description best matches Group VII Flame Effect?
• Which Flame Groups have proximate cast as a feature?
• If not all safety concerns can be seen by one operator, how many enable buttons are required?
• When should temperatures testing stop?
• What characterizes Portable Flame Effects?
• Which term is defined as the source providing oxygen to a combustion reaction?
• What is a Flame Effect Burner?
• Which statement best describes a well ventilated fueling area?
• For Groups II through VII, which mechanism is required to prevent accidental firing?
• Excess fuel that has been removed shall be stored in accordance with which standards?
• If multiple control power sources are available, which arrangement is described as valid for flame effect control systems?
• For a public display permit, what is the minimum general liability insurance amount required?
• During Site Inspection, what area does the operator inspect?
• Which statement defines Permanent Installation?
• Which response should occur if the PME enable signal is not sent or is removed during arming and firing?
• Which statement best describes the minimum control requirements for Flame Group III?
• Which statement is true regarding harm prevention in flame effect control systems?
• Which site plan component relates to storage and holding areas?
• An ignition detection device must not report the presence of an ignition device or pilot due to false sensing of non-fire-related devices.
• Refillable containers shall be refilled and pressurized in a location approved by the AHJ.
• Automatic Flame Effect is defined as
• For permanently installed flame effects, what must the use permit specify?
• Flame effects shall only be fired after they have been confirmed as armed following the completion of the enable and arming process and confirmation that the hazard area is clear.
• Which group requires two fuel shutoff valves, one being a safety shut-off valve, in series?
• Which documents should be available on site and accompany the flame effects equipment?
• Who is required to wear protective clothing?
• The accumulator is defined as
• What best describes a Flame Effect System?
• Fuel Containers and dip buckets must be what when not in use?
• Which scenario would be included in Flame Group IV Type Effect?
• Group IV Flame Effects can be installed only as permanent installations. Which option reflects this?
• Which statement accurately describes Group VI Flame Effect?
• Hybrid Flame Effect is defined as
• Who should operate additional PME devices to ensure operators have a clear view of the area?
• What condition should the premises where flame effect devices are installed and fired be kept in?
• What must spotters always carry?
• What group types are, or can be, manually controlled?
• Who works under the supervision of the flame effect operator?
• Which flame groups have both automatic flame verification and automatic fuel controls?
• Name an Example of a Flame Group IV Type Effect.
• When should the effect valve open?
• If fuel is not provided by a central distribution and supplied directly to a flame effect, how much fuel is permitted?
• Which statement describes Flame Group VI Type Effect?
• Can a municipality or county enact an ordinance or order prohibiting or further regulating flame effects or pyrotechnics beyond these standards?
• Who provides documentation for testing flame effects?
• Where is the accumulator charge valve installed?
• Which description correctly defines a Prepackaged Single-Use Container Valve?
• What must the Flame Effect Operator advise all performers and support personnel of?
• If the ignition means cannot be clearly seen for the entire time, what is required instead of manual arm confirmation?
• Which of the following is an example of a pyrotechnic ignitor use described in the rules?
• When is testing and evaluation documentation for a flame effect provided?
• Can prepackaged single-use containers be refilled?
• Before transporting a portable flame effect, which safety actions must be performed?
• What temperature should components not exceed?
• Which description correctly defines a Prepackaged Single-Use Container Receiver?
• What is the purpose of evaluating flame effects?
• How is Venue defined in the context of flame effects?
• Which item is a Flame Effect Appliance?
• Which statement is true about hybrid flame effects?
• Liability policy countersignature: who must countersign the liability insurance policy?
• For temporarily installed flame effects, what must a use permit specify?
• What must be recorded alongside system pressures when testing?
• Which statement best defines a Use Permit?
• Prior to removing a portable flame effect from one venue and transporting it to another, which steps must be followed?
• The hazard area surrounding a flame effect must be actively monitored and confirmed clear before firing.
• Which description matches Group III Flame Effect?
• What kind of offense is a violation of the Texas Occupational Code under 2154.253 Use of Flame Effects or Pyrotechnics?
• Solid Fuel?
• Which statement best defines a valve in the flame effect system?
• What action should be taken with fuel residue after the performance?
• What does the term Rated refer to?
• If the operator, technical director, or assistant does not have continuous sight of the enable process or hazard area, what arrangement is permitted with approval?
• Which is not a type of Flame Effect Appliance?
• If a building uses flame effects and does not have a complete operational fire-sprinkler system, what must be provided to comply?
• Is LPG lighter or heavier than air?
• If the state fire marshal proposes to suspend, revoke, or refuse to renew a license or permit, the hearing is conducted by which agency?
• In holding areas, which personnel must secure or continuously supervise flammable flame effect materials and loaded devices?
• Which statement correctly describes a Prepackaged Single-Use Container?
• Which description corresponds to Group IV Flame Effect?
• Cast Members
• Flame Group V minimum control requirements include which statements?
• Who bears the overall responsibility for flame effect operations and safety?
• Which statement correctly defines Permanent Installation in terms of permit duration?
• Which statement best describes what enabling comprises in a manually enabled flame effect system?
• Fixed-Location accumulators must be designed and installed so that fuel can be safely removed by
• What defines a Manual Flame Effect?
• Which Flame Groups have automatic fuel controls as a feature?
• Testing flame effects: which statement is true?
• What is the primary requirement for the fire performance area?
• Storage Area is defined as
• If a walk-through demonstration is required, how should it be scheduled?
• For a flame or pyrotechnic effect permit, what is the minimum general liability insurance amount required?
• Who coordinates a Fire Hazard Evaluation?
• Which item is included in the Flame Effect Plan Content as to the production location?
• Where must the additional extinguishers be located for temporary installations?
• Which of the following is NOT listed as NFPA 160 personnel?
• What is an approved method for leak-detection during testing?
• What should the flame effect valve do on loss of the hold-open signal?
• Which statement accurately defines Group VII Flame Effect?
• Why are interlocks required?
• Why are flame effects evaluated?
• Which statement accurately reflects whether fire protection and life safety systems can be completely interrupted during the operation of flame effects?
• What term describes maintaining the premises in neat and orderly condition?
• Where should control system components be located?
• Which flame groups have both unattended and manual fuel controls?
• Which item best describes the safety features of a flame effect control system?
• What is the function of the Accumulator Charge Valve?
• Minimum control requirements for Flame Group IV Flame Effect include which items?
• Why are flame effects tested?
• Who qualifies as Support Personnel in flame effect operations?
• Documentation of Flame Effects Devices and Materials should be available onsite to whom?
• NFPA 1126 and NFPA 160 relate to flame effects. Which statement is true?
• Which Flame Groups have visual (manual) flame verification as a feature?
• Which option best defines a Performer?
• The failure of a device, component, system, or mechanism that results in an immediately dangerous situation is described as?
• What do spotters/firewatch need to be familiar with?
• Which statement about fueling area safety is true?
• During pressure testing, what combination of measurements must be recorded with the system pressure?
• Can a Flame Operator fire an effect that uses a pyrotechnic ignitor?
• All Group II through Group VII control systems need what actions to ensure against accidental firing? 1. Deliberately applies control power 2. Enables or arms the system. Which option describes the required mechanism?
• Which term describes an area where flame effect material or flame effect devices are stored prior to use or movement to a holding area?
• When can Fire Props be refueled?
• The Flame Effect System should be made of which material?
• Where is the Vent Valve typically located in the fuel train?
• What must be done before transporting Liquid-Fuel?
• Which of the following is a requirement for fuels delivered through a central distribution system?
• How should temperatures be taken during testing?
• All components of the flame effect appliance must be compatible with the fuels and operating pressures specified in the design. True or False?
• When piping is used, what pressure should the system be tested at?
• For temporary installations, how many extinguishers are required in total?
• For Flame Group VI, what additional requirement applies when cast members are in close proximity to the flame effect?
• What does AHJ stand for in flame effect safety?
• Which term describes a container that is factory filled with fuel, not to be refilled, and is equipped with a valve that connects to the appliance receiver?
• Which function is included as a requirement for flame effect control systems?
• If arming confirmation is lost during firing or the hazard area becomes unsafe, what should occur?
• For leak testing of modular flame piping, which statement is correct?
• Which term describes an installation lasting longer than 180 days?
• True or False: The operator of any flame effect shall understand and be familiar with the operating manual or instructions.
• Which flame groups have both attended and manual flame verification?
• Enable Button is defined as
• True or False: At least one Texas pyrotechnic special effects operator's licensee must be present on-site at all times where pyrotechnics are used, discharged, or ignited.
• Where must the manual shutoff valve be located for a central fuel distribution system where the point of delivery is outside a building containing the flame effect control system?
• Personal computers and single-board controllers can be used in related applications such as display, logging, and trending of process variables. Which of the following statements is true?
• Which statement is NOT a wick requirement?
• Why must accumulators conform to standards such as the ASME code, DOT regulations, or PED?
• What defines a Flame Effect Appliance?
• Which statement describes Flame Group V Type Effect?
• Before flame effects or pyrotechnics are used inside a building, what announcement to the assembly must be made?
• Which NFPA 160 personnel is explicitly listed as Spotter/Fire Watch?
• A use permit specifies which of the following?
• What must chain grips be made of?
• True or False: There must be an unobstructed path from the fueling area to the performance area.
• Which term best describes the area made hazardous by flame effect operation that is not normally accessible?
• When should an accumulator be charged?
• Which flame group can only be permanent installation?
• What feature should PME pushbuttons provide to confirm the enable signal has been sent?
• Which statement best describes a Flame Effect Plan?
• Where must the manual shutoff valve be installed for central distribution fuels?
• Which outdoor activity is explicitly exempt from these regulations?
• When other safety-critical effects, allied equipment, and other proximate equipment can produce contributory hazards, what should the effect safety controller have?
• Positive confirmation through the use of an interlock or other device of the fuel supply and each auxiliary service is required prior to the continuation of the enable process.
• AHJ stands for which of the following?
• True or False: Emergency operations shall be in accordance with the plan approved by the AHJ.
• Are automatic fuel shutoff valves required when control functions are used?
• What does SDS stand for?
• Who determines whether a locked or obstructed exit door constitutes a violation of the occupational code?
• Who is responsible for observing the accessible hazard area during the entire time a flame effect is enabled and fired?
• Can documentation of the testing and evaluation be prepared by a third party? Under whose approval?